Công tắc an toàn CES-AR-C01-EH-SA (Euchner 098582)
Thông số kỹ thuật công tắc toàn Euchner CES-AR-C01-EH-SA (Order no. 098582)
đại lý euchner | đại lý CES-AR-C01-EH-SA | đại lý 098582
nhà phân phối euchner | nhà phân phối CES-AR-C01-EH-SA | Safety relay 098582
Độ chính xác R | |
according to EN 60947-5-2 |
Electrical connection values
Cầu chì | |
external (operating voltage) | 0.25 … 8 A |
Điện áp cách điện định mức Ui | 300 V (Tested by the employers’ liability insurance association up to 75 V) |
Điện áp chịu xung định mức Uimp | 1.5 kV |
Điện áp hoạt động DC | |
UB | 24 V DC -15% … +15% reverse polarity protected, regulated, residual ripple |
Turn-on time | |
Đầu ra an toàn | max. 400 ms |
EMC yêu cầu bảo vệ | Acc. to EN IEC 60947-5-3 |
Risk time according to EN 60947-5-3 | max. 260 ms |
Risk time according to EN 60947-5-3, extension for each additional device | max. 5 ms |
Cấp an toàn | III |
Mức tiêu thụ dòng điện | |
no load on outputs | max. 50 mA |
Mức độ ô nhiễm (external, according to EN 60947-1) | 3 |
Monitoring output OUT | |
Kiểu đầu ra | p-switching, short circuit-proof |
Điện áp đầu ra | 0.8 x UB … UB V DC (Values at a switching current of 50 mA without taking into account the cable lengths.) |
Chuyển đổi dòng điện | max. 200 mA |
Đầu ra an toàn OA / OB | |
Kiểu đầu ra | Semiconductor outputs, p-switching, short circuit-proof |
Điện áp đầu ra | |
LOW U(OA,OB) | 0 … 1 V DC |
HIGH U(OA,OB) | UB-1.5 … UB V DC (Values at a switching current of 50 mA without taking into account the cable lengths.) |
dòng điện ngắn mạch định mức | max. 100 A |
Thời gian chênh lệch | max. 10 ms |
Danh mục sử dụng | |
DC-13 | 24V 400mA (Caution: outputs must be protected with a free-wheeling diode in case of inductive loads.) |
Off-state current Ir | max. 0.25 mA |
Chuyển đổi dòng điện | |
per safety output | 1 … 400 mA |
Thời lượng xung kiểm tra | max. 1 ms |
Kết nối type | M12 plug connector, 8-pin |
Mô men xoắn | |
Fixing screws | max. 1 Nm |
Thời gian trễ | 10 s |
Định hướng cài đặt | any |
Tần số chuyển đổi | max. 1 Hz |
Khoảng cách lắp đặt | min. 40 mm |
Chống sốc và rung | Acc. to EN IEC 60947-5-3 |
Cấp bảo vệ | IP67 |
Nhiệt độ môi trường | -20 … +55 °C |
Material | |
Thân | Plastic, PBT |
The following applies to the approval according to UL | Operation only with UL Class 2 power supply or equivalent measures |
Actuator CES-A-BPA-098775 (Order no. 098775)

Actuator distance s | |
Minimum distance for side approach direction | min. 6 mm |
Switch-on distance | |
with center offset m=0 | 22 mm (These values apply to surface installation of the actuator on metal.) |
Secured switch-off distance sar | |
with center offset m=0 | max. 58 mm (These values apply to surface installation of the actuator on metal) |
Secured switching distance sao | |
with center offset m=0 | min. 18 mm (These values apply to surface installation of the actuator on metal.) |
Switching hysteresis | |
with center offset m=0 | 1 … 2 mm (These values apply to surface installation of the actuator on metal.) |
Electrical connection values
Power supply | Inductive via read head |
Mô men xoắn | |
Fixing screws | max. 1 Nm |
Định hướng cài đặt | active face opposite read head |
Cấp bảo vệ | IP65/IP67/IP69/IP69K |
Nhiệt độ môi trường | -25 … +70 °C |
Material | |
Thân | Plastic (PBT) |
Components included in the set
Included accessories | 2x safety screws M5x10 |
Kennwerte nach EN ISO 13849-1 / EN IEC 62061
PL | maximaler SIL | PFHD | Kategorie | Gebrauchsdauer | |
---|---|---|---|---|---|
Monitoring of the guard position | PL e | – | 2.1×10-9 | 4 | 20 y |
In combination with actuator CES-A-BPA-098775
Switch-on distance | 22 mm (on surface mounting on aluminum. In a non-metallic environment, the typical operating distances increase to 30 mm) |
Secured switch-off distance sar | max. 58 mm |
Secured switching distance sao | min. 18 mm |
Khoảng cách lắp đặt | |
Switching hysteresis | 1 … 2 mm |