Cảm biến CMS-R-BZD-05V (Euchner 159518)

Thông số kỹ thuật cảm biến Euchner Read heads CMS-R-BZD-05V (Order no. 159518)

đại lý euchner | đại lý CMS-R-BZD-05V | đại lý 159518

nhà phân phối euchner | nhà phân phối CMS-R-BZD-05V | Safety relay 159518

Giá trị kết nối điện

Cầu chì
Power supply / safety contacts, external contact protection	Cầu chì 10 A gG (Parameter dependent on the evaluation units ESM-BA2.. and ESM-BA3..)
dòng điện ngắn mạch định mức	100 A (Parameter dependent on the evaluation units ESM-BA2.. and ESM-BA3..)
Electrical switching frequency
At nominal current 8 A	max. 0.1 Hz (Parameter dependent on the evaluation units ESM-BA2.. and ESM-BA3..)
at I_min = 10 mA	max. 5 Hz (Parameter dependent on the evaluation units ESM-BA2.. and ESM-BA3..)
Chuyển đổi điện áp
DC	24 … 35 V
Monitoring contact DC	max. 35 V
Chuyển đổi điện áp according to UL
according to UL Class 2	max. 24 V AC/DC
Chuyển đổi dòng điện
DC	max. 100 mA
Monitoring contact	max. 100 mA
Switching characteristics	parallel
Switching delay from state change	max. 26 ms (Parameter dependent on the evaluation units ESM-BA2.. and ESM-BA3. Corresponds to the risk time according to EN 60947-5-3. This is the maximum OFF time for the safety outputs following removal of the actuator)

Kết nối type	Hard-wired encapsulated cable with cable end sleeves 0.25 mm²
Number of NO contacts	2 NO contacts with internal fuse, 100 mA each, 1 NO contact as monitoring contact
Mô men xoắn	0.4 … 0.5 Nm
Design	B
Định hướng cài đặt	any (During mounting it must be ensured that the marking arrows on the actuator and the read head are opposite each other.)
Chiều dài cáp	5 m
Tuổi thọ cơ học	100 x 10⁶
Cấp bảo vệ	IP67
Nhiệt độ môi trường	-20 … +80 °C
Material
Cable material	PVC
Thân	Fiber glass reinforced PPS
Method of operation	magnetic, reed contact

Characteristic values according to EN ISO 13849-1 and EN IEC 62061

	Monitoring of the guard position
B_10D	20 x 10⁶

in compliance with	EN ISO 13849-1: 2015; EN 62061: 2005 + AC: 2010 + A1: 2013 + A2: 2015; EN ISO 14119: 2013; EN 60947-5-3: 2013
Classification according to EN IEC 60947-5-3	M3D36AS1

In combination with read head ESM-BA201, ESM-BA202, ESM-BA203, ESM-BA301, ESM-BA302, ESM-BA303, ESM-BA201P, ESM-BA301P and actuator CMS-M-BH

Secured switch-off distance s_ar
with center offset m=0	max. 20 mm (The assured release distance s_ar corresponds to the reset distance.)
Secured switching distance s_ao
with center offset m=0	min. 7 mm (Value applies only if there is no ferromagnetic material in the vicinity of the read head and the actuator.)
Center offset
at s=3 mm read distance	2.5 (Figure only applies if there is no ferromagnetic material in the vicinity of the read head and the actuator.)